- SEE ALSO
- COPYRIGHT AND LICENSE
Algorithm::Backoff::Exponential - Backoff exponentially
This document describes version 0.009 of Algorithm::Backoff::Exponential (from Perl distribution Algorithm-Backoff), released on 2019-06-20.
use Algorithm::Backoff::Exponential; # 1. instantiate my $ab = Algorithm::Backoff::Exponential->new( #consider_actual_delay => 1, # optional, default 0 #max_actual_duration => 0, # optional, default 0 (retry endlessly) #max_attempts => 0, # optional, default 0 (retry endlessly) #jitter_factor => 0.25, # optional, default 0 initial_delay => 5, # required #max_delay => 100, # optional #exponent_base => 2, # optional, default 2 (binary exponentiation) #delay_on_success => 0, # optional, default 0 ); # 2. log success/failure and get a new number of seconds to delay, timestamp is # optional but must be monotonically increasing. # for example, using the parameters initial_delay=5, max_delay=100: my $secs; $secs = $ab->failure(); # => 5 (= initial_delay) $secs = $ab->failure(); # => 10 (5 * 2^1) $secs = $ab->failure(); # => 20 (5 * 2^2) $secs = $ab->failure(); # => 33 (5 * 2^3 - 7) $secs = $ab->failure(); # => 80 (5 * 2^4) $secs = $ab->failure(); # => 100 ( min(5 * 2^5, 100) ) $secs = $ab->success(); # => 0 (= delay_on_success)
Illustration using CLI show-backoff-delays (10 failures followed by 3 successes):
% show-backoff-delays -a Exponential --initial-delay 1 --max-delay 200 \ 0 0 0 0 0 0 0 0 0 0 1 1 1 1 2 4 8 16 32 64 128 200 200 0 0 0
This backoff algorithm calculates the next delay as:
initial_delay * exponent_base ** (attempts-1)
initial_delay is required.
exponent_base is 2 by default (binary exponential). For the first failure attempt (
attempts = 1) the delay equals the initial delay. Then it is doubled, quadrupled, and so on (using the default exponent base of 2).
There are limits on the number of attempts (`max_attempts`) and total duration (`max_actual_duration`).
It is recommended to add a jitter factor, e.g. 0.25 to add some randomness to avoid "thundering herd problem".
new(%args) -> obj
This function is not exported.
Arguments ('*' denotes required arguments):
consider_actual_delay => bool (default: 0)
Whether to consider actual delay.
If set to true, will take into account the actual delay (timestamp difference). For example, when using the Constant strategy of delay=2, you log failure() again right after the previous failure() (i.e. specify the same timestamp). failure() will then return ~2+2 = 4 seconds. On the other hand, if you waited 2 seconds before calling failure() again (i.e. specify the timestamp that is 2 seconds larger than the previous timestamp), failure() will return 2 seconds. And if you waited 4 seconds or more, failure() will return 0.
delay_on_success => ufloat (default: 0)
Number of seconds to wait after a success.
exponent_base => ufloat (default: 2)
initial_delay* => ufloat
Initial delay for the first attempt after failure, in seconds.
jitter_factor => float
How much to add randomness.
If you set this to a value larger than 0, the actual delay will be between a random number between original_delay * (1-jitter_factor) and original_delay * (1+jitter_factor). Jitters are usually added to avoid so-called "thundering herd" problem.
The jitter will be applied to delay on failure as well as on success.
max_actual_duration => ufloat (default: 0)
Maximum number of seconds for all of the attempts (0 means unlimited).
If set to a positive number, will limit the number of seconds for all of the attempts. This setting is used to limit the amount of time you are willing to spend on a task. For example, when using the Exponential strategy of initial_delay=3 and max_attempts=10, the delays will be 3, 6, 12, 24, ... If failures are logged according to the suggested delays, and max_actual_duration is set to 21 seconds, then the third failure() will return -1 instead of 24 because 3+6+12 >= 21, even though max_attempts has not been exceeded.
max_attempts => uint (default: 0)
Maximum number consecutive failures before giving up.
0 means to retry endlessly without ever giving up. 1 means to give up after a single failure (i.e. no retry attempts). 2 means to retry once after a failure. Note that after a success, the number of attempts is reset (as expected). So if max_attempts is 3, and if you fail twice then succeed, then on the next failure the algorithm will retry again for a maximum of 3 times.
max_delay => ufloat
Maximum delay time, in seconds.
min_delay => ufloat (default: 0)
Maximum delay time, in seconds.
Return value: (obj)
Please visit the project's homepage at https://metacpan.org/release/Algorithm-Backoff.
Source repository is at https://github.com/perlancar/perl-Algorithm-Backoff.
Please report any bugs or feature requests on the bugtracker website https://rt.cpan.org/Public/Dist/Display.html?Name=Algorithm-Backoff
When submitting a bug or request, please include a test-file or a patch to an existing test-file that illustrates the bug or desired feature.
This software is copyright (c) 2019 by email@example.com.
This is free software; you can redistribute it and/or modify it under the same terms as the Perl 5 programming language system itself.